Edge-Core ES4625 Скачать руководство пользователя страница 611

Страница: 611 / 674

IP Routing Commands

4-283

show ip ospf border-routers

This command shows entries in the routing table that lead to an Area Border Router
(ABR) or Autonomous System Boundary Router (ASBR).

Command Mode

Privileged Exec

Example

Table 4-90 show ip ospf - display description

Field

Description

Routing Process with ID

Router ID

Supports only single TOS (TOS0) route

Type of service is not supported, so you can only assign one cost

per interface

It is an

router type

The types displayed include internal, area border, or

autonomous system boundary routers

Number of areas in this router

The number of configured areas

Area

identifier

The area address, and area type if backbone, NSSA or stub

Number of interfaces

The number of interfaces attached to this area

SPF algorithm executed

The number of times the shortest path first algorithm has been

executed for this area

Console#show ip ospf border-routers

Destination

Next Hop

Cost

Type

RteType

Area

SPF No

--------------- --------------- ------ ----- -------- --------------- -------

10.1.1.252

10.1.1.253

ABR

INTRA

10.1.0.0

10.2.6.252

10.2.9.253

ASBR

INTER

10.2.0.0

Console#

Table 4-91 show ip ospf border-routers - display description

Field

Description

Destination

Identifier for the destination router

Next Hop

IP address of the next hop toward the destination

Cost

Link metric for this route

Type

Router type of the destination; either ABR, ASBR or both

RteType

Route type; either intra-area or interarea route (INTRA or INTER)

Area

The area from which this route was learned

SPF No

The number of times the shortest path first algorithm has been executed for this

route

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES4625

Отзывы:

Edge-Core ES4625, Руководство по управлению, Страница: 611 / 674

Результаты поиска

Содержание ES4625

Отзывы: