manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 451 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 451

DHCP Commands

4-123

4

DHCP Relay

ip dhcp restart relay

This command enables DHCP relay for the specified VLAN. Use the 

no

 form to 

disable it.

Syntax 

[

no

]

 ip dhcp relay

Default Setting 

Disabled

Command Mode 

Interface Configuration (VLAN)

Command Usage 

This command is used to configure DHCP relay functions for host devices 
attached to the switch. If DHCP relay service is enabled, and this switch sees 
a DHCP request broadcast, it inserts its own IP address into the request so 
the DHCP server will know the subnet where the client is located. Then, the 
switch forwards the packet to the DHCP server on another network. When the 
server receives the DHCP request, it allocates a free IP address for the DHCP 
client from its defined scope for the DHCP client’s subnet, and sends a DHCP 
response back to the DHCP relay agent (i.e., this switch). This switch then 
broadcasts the DHCP response received from the server to the client. 

Example 

In the following example, the device is reassigned the same address.

Related Commands

ip dhcp relay server (4-124)

Table 4-44   DHCP Relay Commands

Command

Function

Mode Page

ip dhcp restart relay

Enables DHCP relay agent

IC

4-123

ip dhcp relay server

Specifies DHCP server addresses for relay

IC

4-124

Console(config)#interface vlan 1
Console(config-if)#ip dhcp relay
Console(config-if)#end
Console#show ip interface

Vlan 1 is up, addressing mode is Dhcp

Interface address is 10.1.0.254, mask is 255.255.255.0, Primary
MTU is 1500 bytes
Proxy ARP is disabled
Split horizon is enabled

Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов