manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 516 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 516

Command Line Interface

4-188

4

show spanning-tree mst configuration

This command shows the configuration of the multiple spanning tree.

Command Mode 

Privileged Exec

Example

VLAN Commands

A VLAN is a group of ports that can be located anywhere in the network, but 
communicate as though they belong to the same physical segment. This section 
describes commands used to create VLAN groups, add port members, specify how 
VLAN tagging is used, and enable automatic VLAN registration for the selected 
interface.

Editing VLAN Groups

Console#show spanning-tree mst configuration
Mstp Configuration Information
--------------------------------------------------------------

Configuration name: R&D
Revision level:0

Instance Vlans

--------------------------------------------------------------

1

2

Console#

Table 4-59   VLAN Commands

Command Groups

Function

Page

Editing VLAN Groups

Sets up VLAN groups, including name, VID and state

4-188

Configuring VLAN 

Interfaces

Configures VLAN interface parameters, including ingress and egress 

tagging mode, ingress filtering, PVID, and GVRP

4-190

Displaying VLAN 

Information

Displays VLAN groups, status, port members, and MAC addresses

4-195

Configuring Private VLANs

Configures private VLANs, including uplink and downlink ports

4-197

Configuring Protocol VLANs Configures protocol-based VLANs based on frame type and protocol 4-198

Table 4-60   Commands for Editing VLAN Groups

Command

Function

Mode

Page

vlan database 

Enters VLAN database mode to add, change, and delete 

VLANs 

GC

4-189

vlan 

Configures a VLAN, including VID, name and state 

VC

4-189

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов