Edge-Core ES4625 Скачать руководство пользователя страница 622 | Manualshive

Страница: 622 / 674

Edge-Core ES4625 Скачать руководство пользователя страница 622

Command Line Interface

4-294

4

show ip ospf summary-address

This command displays all summary address information.

Syntax

show ip ospf summary-address

Command Mode

Privileged Exec

Example

This example shows a summary address and associated network mask.

Related Commands

summary-address (4-270)

show ip ospf virtual-links

This command displays detailed information about virtual links.

Syntax

show ip ospf virtual-links

Command Mode

Privileged Exec

Example

Related Commands

area virtual-link (4-274)

Console#show ip ospf summary-address
10.1.0.0/255.255.0.0
Console#

Console#show ip ospf virtual-links
Virtual Link to router 10.1.1.253 is up
Transit area 10.1.1.0
Transmit Delay is 1 sec
Timer intervals configured, Hello 10, Dead 40, Retransmit 5
Console#

Table 4-101 show ip ospf virtual-links - display description

Field

Description

Virtual Link to router

OSPF neighbor and link state (up or down)

Transit area

Common area the virtual link crosses to reach the target router

Transmit Delay

Estimated transmit delay (in seconds) on the virtual link

Timer intervals

Configuration settings for timer intervals, including Hello, Dead and Retransmit

«
...
620
621
622
623
624
...
»

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов