manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 410 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 410

Command Line Interface

4-82

4

Default

force-authorized

Command Mode

Interface Configuration

Example

dot1x operation-mode

This command allows single or multiple hosts (clients) to connect to an 
802.1X-authorized port. Use the 

no

 form with no keywords to restore the default to 

single host. Use the 

no

 form with the 

multi-host max-count

 keywords to restore the 

default maximum count.

Syntax

dot1x operation-mode

 {

single-host

 | 

multi-host 

[

max-count

 

count

]}

no dot1x operation-mode 

[

multi-host max-count

]

•

single-host

 – Allows only a single host to connect to this port.

•

multi-host

 – Allows multiple host to connect to this port.

•

max-count

 – Keyword for the maximum number of hosts.

count

 – The maximum number of hosts that can connect to a port. 

(Range: 1-1024; Default: 5)

Default

Single-host

Command Mode

Interface Configuration

Command Usage 

• The “max-count” parameter specified by this command is only effective if the 

dot1x mode is set to “auto” by the dot1x port-control command (page 4-105).

• In “multi-host” mode, only one host connected to a port needs to pass 

authentication for all other hosts to be granted network access. Similarly, a 
port can become unauthorized for all hosts if one attached host fails 
re-authentication or sends an EAPOL logoff message.

Example

Console(config)#interface eth 1/2
Console(config-if)#dot1x port-control auto
Console(config-if)#

Console(config)#interface eth 1/2
Console(config-if)#dot1x operation-mode multi-host max-count 10
Console(config-if)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов