manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 557 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 557

Multicast Filtering Commands

4-229

4

Command Usage 

See “Configuring IGMP Snooping and Query Parameters” on page 3-171 for a 
description of the displayed items.

Example 

The following shows the current IGMP snooping configuration:

show mac-address-table multicast 

This command shows known multicast addresses.

Syntax 

show mac-address-table multicast

 [

vlan

 

vlan-id

] [

user

|

igmp-snooping

]

•

vlan-id

 - VLAN ID (1 to 4093) 

•

user

 - Display only the user-configured multicast entries. 

•

igmp-snooping

 - Display only entries learned through IGMP snooping. 

Default Setting 

None

Command Mode 

Privileged Exec

Command Usage 

Member types displayed include IGMP or USER, depending on selected 
options.

Example 

The following shows the multicast entries learned through IGMP snooping for 
VLAN 1:

Console#show ip igmp snooping

Service status:

Enabled

Querier status:

Disabled

Query count:

2

Query interval:

125 sec

Query max response time: 10 sec
Router port expire time: 300 sec
IGMP snooping version:

Version 2

Console#

Console#show mac-address-table multicast vlan 1 igmp-snooping

VLAN M'cast IP addr. Member ports Type
---- --------------- ------------ -------

1

224.1.2.3

Eth1/11

IGMP

Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов