manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 496 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 496

Command Line Interface

4-168

4

clear mac-address-table dynamic

This command removes any learned entries from the forwarding database and 
clears the transmit and receive counts for any static or system configured entries.

Default Setting 

None

Command Mode 

Privileged Exec

Example 

show mac-address-table

This command shows classes of entries in the bridge-forwarding database.

Syntax 

show mac-address-table

 [

address

 

mac-address

 [

mask

]] [

interface

 

interface

] 

[

vlan

 

vlan-id

] [

sort

{

address

|

vlan

 | 

interface

}]

•

mac-address

 - MAC address.

•

mask

 - Bits to match in the address. 

•

interface

 

•

ethernet

 

unit

/

port

-

unit

 - Stack unit. (Range: 1-8)

-

port

 - Port number. (Range: 1-25/49)

•

port-channel

 

channel-id

 (Range: 1-32) 

•

vlan-id

 - VLAN ID (Range: 1-4093) 

•

sort

 - Sort by address, vlan or interface. 

Default Setting 

None

Command Mode 

Privileged Exec

Command Usage 

• The MAC Address Table contains the MAC addresses associated with each 

interface. Note that the Type field may include the following types:
- Learned - Dynamic address entries
- Permanent - Static entry
- Delete-on-reset - Static entry to be deleted when system is reset

• The mask should be hexadecimal numbers (representing an equivalent bit 

mask) in the form xx-xx-xx-xx-xx-xx that is applied to the specified MAC 
address. Enter hexadecimal numbers, where an equivalent binary bit “0” 

Console#clear mac-address-table dynamic
Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов