Edge-Core ES4625 Скачать руководство пользователя страница 448 | Manualshive

Страница: 448 / 674

Edge-Core ES4625 Скачать руководство пользователя страница 448

Command Line Interface

4-120

4

the user resides. Then use the

snmp-server user

command to specify the

user and the IP address for the remote device where the user resides. The
remote agent’s SNMP engine ID is used to compute authentication/privacy
digests from the user’s password. If the remote engine ID is not first configured,
the

snmp-server user

command specifying a remote user will fail.

• SNMP passwords are localized using the engine ID of the authoritative agent.

For informs, the authoritative SNMP agent is the remote agent. You therefore
need to configure the remote agent’s SNMP engine ID before you can send
proxy requests or informs to it.

Example

show snmp user

This command shows information on SNMP users.

Command Mode

Privileged Exec

Example

Console(config)#snmp-server user steve group r&d v3 auth md5 greenpeace

priv des56 einstien

Console(config)#snmp-server user mark group r&d remote 192.168.1.19 v3

auth md5 greenpeace priv des56 einstien

Console(config)#

Console#show snmp user
EngineId: 800000ca030030f1df9ca00000
User Name: steve
Authentication Protocol: md5
Privacy Protocol: des56
Storage Type: nonvolatile
Row Status: active

SNMP remote user
EngineId: 80000000030004e2b316c54321
User Name: mark
Authentication Protocol: mdt
Privacy Protocol: des56
Storage Type: nonvolatile
Row Status: active

Console#

Table 4-41 show snmp user - display description

Field

Description

EngineId

String identifying the engine ID.

User Name

Name of user connecting to the SNMP agent.

Authentication Protocol

The authentication protocol used with SNMPv3.

Privacy Protocol

The privacy protocol used with SNMPv3.

Storage Type

The storage type for this entry.

«
...
446
447
448
449
450
...
»

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов