manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 504 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 504

Command Line Interface

4-176

4

spanning-tree mst-configuration 

This command changes to Multiple Spanning Tree (MST) configuration mode. 

Default Setting 

• No VLANs are mapped to any MST instance.
• The region name is set the switch’s MAC address.

Command Mode 

Global Configuration

Example 

Related Commands 

mst vlan (4-176)
mst priority (4-177)
name (4-177)
revision (4-178)
max-hops (4-179)

mst vlan

This command adds VLANs to a spanning tree instance. Use the 

no

 form to remove 

the specified VLANs. Using the 

no

 form without any VLAN parameters to remove all 

VLANs. 

Syntax 

[

no

] 

mst

 

instance_id

 

vlan

 

vlan-range

•

instance_id

 - Instance identifier of the spanning tree. (Range: 0-4094)

•

vlan-range

 - Range of VLANs. (Range: 1-4093)

Default Setting 

none

Command Mode 

MST Configuration

Command Usage 

• Use this command to group VLANs into spanning tree instances. MSTP 

generates a unique spanning tree for each instance. This provides multiple 
pathways across the network, thereby balancing the traffic load, preventing 
wide-scale disruption when a bridge node in a single instance fails, and 
allowing for faster convergence of a new topology for the failed instance. 

• By default all VLANs are assigned to the Internal Spanning Tree (MSTI 0) that 

connects all bridges and LANs within the MST region. This switch supports up 
to 58 instances. You should try to group VLANs which cover the same general 
area of your network. However, remember that you must configure all bridges 
within the same MSTI Region (page 4-177) with the same set of instances, 

Console(config)#spanning-tree mst-configuration
Console(config-mstp)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов