manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 373 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 373

System Management Commands

4-45

4

Default Setting 

Flash: errors (level 3 - 0)
RAM: warnings (level 7 - 0)

Command Mode 

Global Configuration

Command Usage 

The message level specified for flash memory must be a higher priority (i.e., 
numerically lower) than that specified for RAM.

Example 

logging host

This command adds a syslog server host IP address that will receive logging 
messages. Use the 

no

 form to remove a syslog server host.

Syntax 

[

no

]

 logging host

 

host_ip_address

host_ip_address

 - The IP address of a syslog server.

Default Setting 

None

Command Mode 

Global Configuration

Command Usage 

• By using this command more than once you can build up a list of host IP 

addresses.

• The maximum number of host IP addresses allowed is five.

Example 

logging facility

This command sets the facility type for remote logging of syslog messages. Use the 

no

 form to return the type to the default.

Syntax 

[

no

]

 logging facility

 

type

type

 - A number that indicates the facility used by the syslog server to 

dispatch log messages to an appropriate service. (Range: 16-23)

Console(config)#logging history ram 0
Console(config)#

Console(config)#logging host 10.1.0.3
Console(config)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов