manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 282 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 282

Configuring the Switch

3-230

3

•

Authentication Key

 – Specifies the key to use for authenticating RIPv2 packets. 

For authentication to function properly, both the sending and receiving interface 
must use the same password. (Range: 1-16 characters, case sensitive)

Web -

 Click Routing Protocol, RIP, Interface Settings. Select the RIP protocol 

message types that will be received and sent, the method used to provide faster 
convergence and prevent loopback (i.e., prevent instability in the network topology), 
and the authentication option and corresponding password. Then click Apply. 

Figure 3-133   RIP Interface Settings

CLI -

 This example sets the receive version to accept both RIPv1 or RIPv2 

messages, the send mode to RIPv1 compatible (i.e., called v2-broadcast in the CLI), 
sets the method of preventing instability in the network topology to Split Horizon, 
enables authentication via a simple password (i.e., called text mode in the CLI).

Console(config)#interface vlan 1

4-143

Console(config-if)#ip rip receive version 1 2

4-258

Console(config-if)#ip rip send version v2-broadcast

4-259

Console(config-if)#ip split-horizon

4-260

Console(config-if)#ip rip authentication mode text

4-261

Console(config-if)#ip rip authentication key mighty

4-260

Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов