manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 517 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 517

VLAN Commands

4-189

4

vlan database

This command enters VLAN database mode. All commands in this mode will take 
effect immediately.

Default Setting 

None

Command Mode 

Global Configuration

Command Usage 

• Use the VLAN database command mode to add, change, and delete VLANs. 

After finishing configuration changes, you can display the VLAN settings by 
entering the 

show vlan

 command. 

• Use  the 

interface vlan

 command mode to define the port membership mode 

and add or remove ports from a VLAN. The results of these commands are 
written to the running-configuration file, and you can display this file by 
entering the 

show running-config

 command. 

Example 

Related Commands 

show vlan (4-196)

vlan

This command configures a VLAN. Use the 

no

 form to restore the default settings or 

delete a VLAN.

Syntax 

vlan

 

vlan-id

 [

name

 

vlan-name

] 

media ethernet

 [

state

 {

active

 | 

suspend

}]

no vlan

 

vlan-id

 [

name

 | 

state

]

•

vlan-id

 - ID of configured VLAN. (Range: 1-4093, no leading zeroes) 

•

name

 - Keyword to be followed by the VLAN name. 

-

vlan-name

 - ASCII string from 1 to 32 characters. 

•

media ethernet

 - Ethernet media type. 

•

state

 - Keyword to be followed by the VLAN state. 

-

active

 - VLAN is operational. 

-

suspend

 - VLAN is suspended. Suspended VLANs do not pass packets. 

Default Setting 

By default only VLAN 1 exists and is active.

Command Mode 

VLAN Database Configuration

Console(config)#vlan database
Console(config-vlan)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов