Edge-Core ES4625 Скачать руководство пользователя страница 447

Страница: 447 / 674

SNMP Commands

4-119

snmp-server user

This command adds a user to an SNMP group, restricting the user to a specific
SNMP Read, Write, or Notify View. Use the

form to remove a user from an SNMP

group.

Syntax

snmp-server user

username

groupname

[

remote

ip-address

] {

v2c

[

encrypted

] [

auth

{

md5

sha

}

auth-password

[

priv des56

priv-password

]]

no snmp-server user

username

{

v2c

remote

}

•

username

- Name of user connecting to the SNMP agent.

(Range: 1-32 characters)

• groupname -

Name of an SNMP group to which the user is assigned.

(Range: 1-32 characters)

•

remote

- Specifies an SNMP engine on a remote device.

•

ip-address

- The Internet address of the remote device.

•

v2c

- Use SNMP version 1, 2c or 3.

•

encrypted

- Accepts the password as encrypted input.

•

auth

- Uses SNMPv3 with authentication.

•

md5

sha

- Uses MD5 or SHA authentication.

•

auth-password

- Authentication password. Enter as plain text if the

encrypted

option is not used. Otherwise, enter an encrypted password.

(A minimum of eight characters is required.)

•

priv des56

- Uses SNMPv3 with privacy with DES56 encryption.

•

priv-password

- Privacy password. Enter as plain text if the

encrypted

option is not used. Otherwise, enter an encrypted password.

Default Setting

None

Command Mode

Global Configuration

Command Usage

• The SNMP engine ID is used to compute the authentication/privacy digests

from the password. You should therefore configure the engine ID with the

snmp-server engine-id

command before using this configuration command.

• Before you configure a remote user, use the

snmp-server engine-id

command (page 4-113) to specify the engine ID for the remote device where

writeview

The associated write view.

notifyview

The associated notify view.

storage-type

The storage type for this entry.

Row Status

The row status of this entry.

Table 4-40 show snmp group - display description

(Continued)

Field

Description

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES4625

Отзывы:

Edge-Core ES4625, Руководство по управлению, Страница: 447 / 674

Результаты поиска

Содержание ES4625

Отзывы: