Edge-Core ES4625 Скачать руководство пользователя страница 380

Страница: 380 / 674

Command Line Interface

4-52

Command Usage

You can specify up to five recipients for alert messages. However, you must
enter a separate command to specify each recipient.

Example

logging sendmail

This command enables SMTP event handling. Use the

form to disable this

function.

Syntax

[

]

logging sendmail

Default Setting

Enabled

Command Mode

Global Configuration

Example

show logging sendmail

This command displays the settings for the SMTP event handler.

Command Mode

Normal Exec, Privileged Exec

Example

Console(config)#logging sendmail destination-email [email protected]
Console(config)#

Console(config)#logging sendmail
Console(config)#

Console#show logging sendmail
SMTP servers
-----------------------------------------------
192.168.1.19

SMTP minimum severity level: 7

SMTP destination email addresses
-----------------------------------------------
[email protected]

SMTP source email address: [email protected]

SMTP status: Enabled
Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES4625

Отзывы:

Edge-Core ES4625, Руководство по управлению, Страница: 380 / 674

Результаты поиска

Содержание ES4625

Отзывы: