manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 396 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 396

Command Line Interface

4-68

4

Command Usage 

• If you enter the command 

dir

 without any parameters, the system displays all 

files. 

• A colon (:) is required after the specified unit number. 
• File information is shown below:

Example 

The following example shows how to display all file information:

whichboot

This command displays which files were booted when the system powered up.

Syntax 

whichboot

 [

unit

]

unit 

- Stack unit. (Range: 1-8)

Default Setting 

None

Command Mode 

Privileged Exec

Table 4-26   File Directory Information

Column Heading

Description

file name

The name of the file.

file type

File types: Boot-Rom, Operation Code, and Config file.

startup

Shows if this file is used when the system is started.

size

The length of the file in bytes.

Console#dir
          file name                        file type       startup size (byte)
 -------------------------------------     --------------  ------- -----------
 Unit1:
          D1014                            Boot-Rom Image  Y           825336
          V1000-F                          Operation Code  N          3504992
          V31121                           Operation Code  Y          4951408
          Factory_Default_Config.cfg       Config File     N              455
          startup1.cfg                     Config File     Y             7996
 ---------------------------------------------------------------------------
                                                  Total free space:  22675456
Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов