Edge-Core ES4625 Скачать руководство пользователя страница 338

Страница: 338 / 674

Command Line Interface

4-10

Command Groups

The system commands can be broken down into the functional groups shown below

Table 4-4 Command Group Index

Command Group

Description

Page

Line

Sets communication parameters for the serial port and Telnet,

including baud rate and console time-out

4-11

General

Basic commands for entering privileged access mode, restarting the

system, or quitting the CLI

4-20

System Management

Controls system logs, system passwords, user name, browser

management options, and a variety of other system information

4-25

Flash/File

Manages code image or switch configuration files

4-64

Authentication

Configures logon access using local or remote authentication;

also configures port security and IEEE 802.1X port access control

4-70

Access Control List

Provides filtering for IP frames (based on address, protocol, TCP/UDP

port number or TCP control code) or non-IP frames (based on MAC

address or Ethernet type)

4-87

SNMP

Activates authentication failure traps; configures community access

strings, and trap managers

4-107

DHCP

Configures DHCP client, relay and server functions

4-121

DNS

Configures DNS services.

4-136

Interface

Configures the connection parameters for all Ethernet ports,

aggregated links, and VLANs

4-143

Mirror Port

Mirrors data to another port for analysis without affecting the data

passing through or the performance of the monitored port

4-154

Rate Limiting

Controls the maximum rate for traffic transmitted or received on a port

4-156

Link Aggregation

Statically groups multiple ports into a single logical trunk; configures

Link Aggregation Control Protocol for port trunks

4-157

Address Table

Configures the address table for filtering specified addresses, displays

current entries, clears the table, or sets the aging time

4-166

Spanning Tree

Configures Spanning Tree settings for the switch

4-170

VLANs

Configures VLAN settings, and defines port membership for VLAN

groups; also enables or configures private VLANs and protocol VLANs

4-188

GVRP and

Bridge Extension

Configures GVRP settings that permit automatic VLAN learning;

shows the configuration for the bridge extension MIB

4-202

Priority

Sets port priority for untagged frames, selects strict priority or weighted

round robin, relative weight for each priority queue, also sets priority for

TCP/UDP traffic types, IP precedence, and DSCP

4-206

Quality of Service

Configures Differentiated Services

4-218

Multicast Filtering

Configures IGMP multicast filtering, query parameters, and specifies

ports attached to a multicast router

4-226

IP Interface

Configures IP address for the switch interfaces; also configures ARP

parameters and static entries

4-241

IP Routing

Configures static and dynamic unicast routing

4-249

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES4625

Отзывы:

Edge-Core ES4625, Руководство по управлению, Страница: 338 / 674

Результаты поиска

Содержание ES4625

Отзывы: