Baumuller b maXX BM5800 Скачать руководство пользователя страница 566 | Manualshive

Страница: 566 / 816

background image

Operating Modes

Parameter manual

b maXX

BM5800

Document No.: 5.16029.03

Baumüller Nürnberg GmbH

566

3.8

3.8.3.6 Automatic setting of the absolute value offset at homing

Applications using absolute encoders, automatically copy the absolute value offset (M0-
Offset) to the corresponding parameters (

) at the end of homing. Pa-

rameter

Homing mode, bit 6 activates this behavior. If bit 6 is active, the param-

eter

Revolution overflow counter is deleted also.

The absolute value offset is the shift between the encoder coordinate system (the abso-
lute encoder actual value as read from absolute value encoder) and the position coordi-
nate system redefined by homing (machine coordinate system). This absolute value
offset is considered at initialization of the encoder. This way, a positioning coordinate sys-
tem occurs, which is the same, as it would be after homing.

Figure 151:

Absolute value offset

3.8.3.7 Notes

Switch wiring

The end and reference switches can be wired as closers or openers. The type of wiring
can be adjusted in the drive using the configuration of the digital inputs. Wiring as an
opener is recommended for safety reasons (detection of wire breaks).

Limit switch

The hardware or software limit switches do not limit the adjusting range during the homing
runs!

The limit switches must be designed so that they cannot be overridden. The option to
leave the switching mode "actuated" with the negative limit switch should only be avail-
able in positive direction and only in negative direction with positive limit switch.

Problem during
Homing

If homing is not completed after the reference switch is reached (response through bit 10
of

Status word does not occur), this may be due to the settings for the position-

ing window (

). The drive must be in the positioning window for the period of po-

sitioning window time that was set after the home position has been reached. The
positioning window may be adjusted too small so that this requirement cannot be met.

Reproducibility

To reach identical home positions, the following conditions must be met:

m

The homing speeds, acceleration, deceleration and encoder offset may not be
changed after the one-time adjustment.

m

The homing speed must be reached in Phase 1.

0

0

Encoder
coordinates

Position
coordinates

M0 offset

Reference point

«
...
564
565
566
567
568
...
»

Содержание b maXX BM5800

















































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для b maXX BM5800

Бренд: S-COM Страницы: 400

Бренд: Manfrotto Страницы: 16

Бренд: jablotron Страницы: 22

Бренд: jablotron Страницы: 2

Бренд: LAE electronic Страницы: 7

Бренд: LAE electronic Страницы: 2

Бренд: LAS Страницы: 6

GA Industries 930-DT

Бренд: Vag Страницы: 4

Бренд: ZPA Pecky, a.s. Страницы: 36

Бренд: WAGNER Страницы: 128

Бренд: Samson Страницы: 36

WisBlock RAK19012

Бренд: RAK Страницы: 12

Бренд: Cypress Semiconductor Страницы: 36

Бренд: FUHR Страницы: 20

Бренд: GCE Страницы: 13

Бренд: Leviton Страницы: 2

Бренд: TECH Страницы: 20

Бренд: Samson Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды