3) Remove back door balancer (first at its door-side and next at its
body-side).
4) Remove door hinge bolts and door.
WARNING:
Handling of Back Door Balancer (Damper)
Do not disassemble balancer because its cylinder
is filled with gas.
The gas itself is harmless but it may issue out of the
hole together with chips generated by the drill.
Therefore, be sure to wear goggle.
When discarding removed back door balancer
(damper), use a 2 to 3 mm (0.08 to 0.12 in.) drill to
make a hole as shown.
Handle balancer carefully. Do not scar or scratch
exposed surface of its piston rod, and never allow
any paint or oil to stick to its surface.
Do not turn piston rod with balancer fully extended.
INSTALLATION
Reverse removal procedure to install back door by note the follow-
ing procedure.
NOTE:
When replacing back door, coat replacement door inside with
wax for proper anticorrosive treatment. Refer to RUST PROOF
TREATMENT AREA in this section.
Install back door with applying rust proof sealant to hinge fitting
surface.
Secure wiring harness and connect couplers.
Install door latch striker with its arrow mark indicating front side
of vehicle.
Adjust the door latch striker so that striker center aligns with the
center of grove in door latch base.
To adjust door latch and striker each other, insert proper number
of shims below the bottom of striker.
For correct installation, see PANEL CLEARANCE and adjust
door hinge properly.
1. Door latch
2. Shim
3. Door latch striker
4. Forward
BODY SERVICE
9-15
Summary of Contents for GA413
