Siemens Simatic ET200pro Operating Instructions Manual Download Page 98

Page: 98 / 545

Connection

4.8 Connecting the IM 154-4 PN High Feature interface module with CM IM PN M12, 7/8"

ET 200pro distributed I/O system

Operating Instructions, 03/2013, A5E00335544-08

Connecting M12 and 7/8" cable connectors

Press the M12 and 7/8" cable connectors into the corresponding circular socket

connectors of the CM IM PN M12, 7/8" connection module. Ensure that the locking

mechanism between the connector and socket is properly applied.

Tighten the knurled screws of the connectors (torque = 1.5 Nm).

Figure 4-14 Connecting M12 and 7/8" cable connectors

NOTICE
Removing the 7/8" cable connector
It is not permissible to remove the 7/8" cable connectors while ET 200pro is in operation!

Always switch off the 1L+ electronics/encoder supply and the 2L+ load voltage supply

before you pull or plug the 7/8" cable connector.

Note
If you remove the M12 or 7/8" cable connector used for forwarding, downstream modules

on PROFINET IO will fail or will no longer be supplied with power.

Covering unused sockets

Always close all unused sockets using M12 and 7/8" caps in order to achieve degree of

protection IP65, IP66 or IP67.

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands