Siemens Simatic ET200pro Operating Instructions Manual Download Page 133

Page: 133 / 545

Connection

4.13 Connecting the Power Module with the CM PM-E ECOFAST Connection Module

ET 200pro distributed I/O system
Operating Instructions, 03/2013, A5E00335544-08

133

Pin assignment of the ECOFAST cable connector

View of the ECOFAST cable connector

Terminal

Assignment X01

Feed for X01
1

Not assigned

Ground for load voltage supply 2M

2L+ load voltage supply

Connecting the ECOFAST cable connectors

Insert the CM PM ECOFAST connection module into the power module.

Screw the CM PM ECOFAST connection module onto the power module

(torque = 1.5 Nm). Tighten both screws evenly. The screws are already inserted in the

connection module.

Open the interlock for the ECOFAST cable connector on the connection module.

Plug the ECOFAST cable connector (2L+) into the socket of the connection module.

Close the interlock for the ECOFAST cable connector.

NOTICE

It is not allowed to remove the ECOFAST cable connector while ET 200pro is in

operation! Always switch off the load voltage supply (2L+) before you remove the

ECOFAST cable connector.

Note
Removal of the ECOFAST cable connector interrupts the supply to all downstream

modules.

Closing the unused socket

Always close any unused ECOFAST sockets using a cap in order to achieve the degree of

protection IP65, IP66 or IP67.

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands