Siemens Simatic ET200pro Operating Instructions Manual Download Page 353

Page: 353 / 545

Digital electronic modules

14.5 Digital electronic module 4 DO DC 24V/2.0A High Feature (6ES7142-4BD00-0AB0)

ET 200pro distributed I/O system
Operating Instructions, 03/2013, A5E00335544-08

353

Technical specifications

Technical specifications
Dimensions and weight
Dimensions W x H x D (mm)

45 x 130 x 35; with bus module, without

connection module

Weight

Approx. 140 g

Digital outputs
Number of outputs

Support of isochronous mode

Cable length, unshielded

Max. 30 m

Short-circuit protection of the output

Yes, electronic, per channel

•

Response threshold

Min. 2.8 A

Voltages and currents
Rated load voltage 2L+

24 V DC

•

Reverse polarity protection

Yes, per module, against destruction, loads

actuated

•

Short-circuit protection

Yes; per channel

Total current of the outputs

•

All mounting positions up to 40 °C

6 A

•

All mounting positions up to 55 °C

4 A

Current consumption

•

From backplane bus

< 30 mA

•

From load voltage 2L+

< 40 mA

Power loss of the module

Typ. 2.5 W

Electrical isolation

•

Between channels and backplane bus

Yes

•

Between backplane bus and all other circuit

elements

Yes

•

Between channels and electronics power

supply

Yes

•

Between channels

Permitted potential difference

•

Between different electric circuits

75 V DC, 60 V AC

Isolation
Isolation tested

500 V DC

Status, interrupts, diagnostics
Status display

Green LED, per channel

Interrupts

•

Diagnostic interrupt

Configurable

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands