Siemens Simatic ET200pro Operating Instructions Manual Download Page 48

Page: 48 / 545

Mounting

3.2 Rack

ET 200pro distributed I/O system

Operating Instructions, 03/2013, A5E00335544-08

Required tools

●

Wrench or screwdriver, matching the selected fixing screws.

●

Stripping tool and crimp tool for the grounding cable.

Required accessories

Table 3- 1

Rack and grounding cable

For...

you can use...

Description

Outer fixing screws M8 cylindrical head screw in accordance

with ISO 1207/ISO 1580

(DIN 84/DIN 85)

Select the screw length to match

your setup.
You also need 8.4 mm washers

according to ISO 7092 (DIN 433)

M8 hexagonal head screw according to

ISO 4017 (DIN 4017)

Grounding cable

Insulated cable, conductor cross-

section: min. 4 mm

You also need an M8 ring cable lug

and an M8 spring lock washer

Mounting the rack and connecting functional ground (FG)

If necessary, mark the mounting holes on the mounting base, then drill holes with a

diameter of 8.5 mm

±0.2

mm.

Screw-mount (M8 screws) the rack onto the carrier.

Strip the grounding conductor and functional ground (FG) (Cu braid, for example), then

crimp on an M8 ring cable lug.

Fasten the grounding conductor using one of the bore holes of the rack: Slip the spring

lock washer, the washer and the cable lug onto the mounting screw, then screw the rack

onto the carrier.

Connect the opposite end of the grounding cable to ground potential.

Note
Ensure adequate equipotential bonding.

Figure 3-3

Grounding a narrow rack

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands