Siemens Simatic ET200pro Operating Instructions Manual Download Page 140

Page: 140 / 545

Configuring

5.1 PROFIBUS DP

ET 200pro distributed I/O system

140

Operating Instructions, 03/2013, A5E00335544-08

5.1.2

Configuring by Means of GSD File

Introduction

The GSD file allows you to configure ET 200pro using a (previous) STEP 7 version,

COM PROFIBUS, or other software. For this purpose, the GSD file must be installed in the

configuration software beforehand.

Requirements

You require a GSD file, available for download from the Internet at:
GSD file (

http://support.automation.siemens.com

)

●

Interface module IM 154-1 DP:
–

GSD file SI018118.GSG for 6ES7154-1AA01-0AB0

–

GSD file SIEM8118.GSG for 6ES7154-1AA00-0AB0

●

Interface module IM 154-2 DP High Feature:
–

GSD file SI018119.GSG for 6ES7154-2AA01-0AB0

–

GSD file SIEM8119.GSG for 6ES7154-2AA00-0AB0

Configuring ET 200pro on PROFIBUS DP in STEP 7

Start STEP 7, then select Options > Install New GSD File in HW Config.

Select the GSD file to install from the next dialog box, then confirm with OK. Result:

ET 200pro appears in the PROFIBUS DP folder of the hardware catalog.

The further procedure is the same as in Configuring in STEP 7 (Page 139).

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands