Siemens Simatic ET200pro Operating Instructions Manual Download Page 102

Page: 102 / 545

Connection

4.9 Connecting the IM 154-4 PN High Feature Interface Module with CM IM PN PP Cu

ET 200pro distributed I/O system

102

Operating Instructions, 03/2013, A5E00335544-08

Connecting push-pull cable connector

Plug the push-pull cable connector for 1L+/2L+ and RJ45 into the associated sockets on the

CM IM PN PP Cu connection module. The connectors must engage. Ensure that the locking

mechanism between the connector and socket is properly applied.

Figure 4-15 Connecting push-pull cable connector

NOTICE
Removing the push-pull cable connectors
It is not permissible to remove the push-pull cable connector for 1L+/2L+ while ET 200pro is

in operation! Always switch off the 1L+ electronics/encoder supply and the 2L+ load voltage

supply before you pull or plug the push-pull cable connector.

Note
If you remove the push-pull cable connector used for looping through of PROFINET IO or

1L+/2L+, the downstream modules on PROFINET IO will fail or will no longer be supplied

with power.

Covering unused sockets

Cover all unused push-pull sockets with caps in order to achieve degree of protection IP65,

IP66, or IP67.

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands