Siemens Simatic ET200pro Operating Instructions Manual Download Page 218

Page: 218 / 545

Alarm, error and system messages

9.2 PROFINET IO

ET 200pro distributed I/O system

218

Operating Instructions, 03/2013, A5E00335544-08

Status and error displays GE, BF, ON, LINK, RX/TX, FO

Table 9- 4

Status and error displays of the IM 154-4 PN High Feature on port 1 (P1) and port 2 (P2)

LEDs

Meaning

Remedy

LINK

RX/TX

P1 FO

Off

No connection to the IO controller

(no IO controller available on the network)

•

Set uniform baud rate

•

Autonegotiation not successful

There is a connection to the IO controller.

Correct operation

Transmission/reception is in progress

Maintenance demanded:

Attenuation through the fiber-optic cable is so

high that operation will soon no longer be

possible.

Check the affected data transmission link for

the following causes:

•

Damage to the fiber-optic cable

•

Correct installation of the PROFINET

connector/PROFINET connections

•

Adherence to the max. length of 50 m for

POF cables

•

Check that the FOC connector is firmly

seated

*) not relevant

LEDs

Meaning

Remedy

LINK

RX/TX

P2 FO

For meaning, see LEDs on port 1 (P1)

Maintenance information MAINT

Maintenance information can indicate a maintenance requirement or maintenance request.

The MAINT LED lights up yellow when maintenance information from PROFINET is

available (see Maintenance alarms (Page 221)). An alarm message is generated in addition

to the LED display.

24 V DC status indicator

The green 24 V DC LED is lit when the 2L+ load voltage supply is connected. If the LED is

not lit, check to see if the power supply is switched on and the fuse is functioning.

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands