Siemens Simatic ET200pro Operating Instructions Manual Download Page 200

Page: 200 / 545

Alarm, error and system messages

9.1 PROFIBUS DP

ET 200pro distributed I/O system

200

Operating Instructions, 03/2013, A5E00335544-08

9.1.6

Station states 1 to 3

Definition

Station states 1 to 3 provide an overview of the status of a DP slave.

Structure of station status 1 (byte 0)

Bit

Meaning

Cause/remedy

0 1: The DP master cannot address the DP slave.

•

Check the PROFIBUS address of the DP slave.

•

Check the PROFIBUS DP connection.

•

Check the power supply to the DP slave.

•

Check the settings of the RS 485 repeater.

•

Check whether the DP slave was reset.

1 1: The DP slave is not yet ready to exchange data.

•

Wait, the DP slave is currently starting up.

2 1: The configuration data transferred from the DP

master to the DP slave does not match the DP

slave configuration.

•

Verify the station type and configuration of the DP slave in

the configuring software.

3 1: External diagnostic information exists.

(group diagnosis display)

•

Evaluate the ID-specific and/or channel-specific diagnostic

information, and the module status. Bit 3 is reset after all

errors are cleared. The bit will be set again if a new

diagnostic message is output in the bytes of the

diagnostics functions mentioned above.

4 1: The DP slave does not support the requested

function (modification of the PROFIBUS address in

the software, for example).

•

Check the configuration.

5 1: The DP master cannot interpret the response of

the DP slave.

•

Check the bus configuration.

6 1: The DP slave type does not match the software

configuration.

•

Compare the preset to the actual configuration

7 1: The DP slave was parameterized by a different

DP master (not by the DP master which currently

has access to the DP slave).

•

The bit is always 1 if, for example, you are currently

accessing the DP slave from the PG or a different DP

master.

•

The PROFIBUS address of the DP master which has

parameterized the DP slave is in the "Master PROFIBUS

address" diagnostics byte.

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands