Siemens Simatic ET200pro Operating Instructions Manual Download Page 70

Page: 70 / 545

Connection

4.2 Operation of the ET 200pro with Grounded Reference Potential

ET 200pro distributed I/O system

Operating Instructions, 03/2013, A5E00335544-08

Overall configuration of ET 200pro

The figure below shows the overall configuration of the ET 200pro distributed I/O system

(load voltage supply and grounding concept) with infeed from a TN-S network.

①

Disconnecting device for control system, signal transmitters and final controlling elements

②

Short-circuit and overload protection

③

The connection between 1M and FE is not applicable in an ET 200pro configuration with

ungrounded reference potential.

④

Ground busbar

⑤

Fuses for line protection

Note
When ET 200pro is operated with ungrounded reference potential and 1M and FE are not

interconnected, any interference currents will be discharged to protective ground via an

internal RC circuit.

Insulation monitoring

Insulation monitoring must be provided in the following cases:

●

In an ET 200pro configuration with ungrounded reference potential

●

If hazardous plant states can be expected as a result of faults.

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands