Siemens Simatic ET200pro Operating Instructions Manual Download Page 412

Page: 412 / 545

Analog electronic modules

15.5 Analog electronic module 4 AO U High Feature (6ES7145-4FF00-0AB0)

ET 200pro distributed I/O system

412

Operating Instructions, 03/2013, A5E00335544-08

Technical specifications
Analog value generation
Conversion principle

R network

Conversion time per channel, in ms

0.7 ms

•

Cycle time in ms

(see Appendix

Response times

)

Number of active channels per module x

conversion time

•

Resolution (including overrange)

± 10 V/15 bit + sign

1 V to 5 V/14 bit

0 V to 10 V/15 bit

Settling time

•

With resistive load

0.1 ms

•

With capacitive load

6 ms

Injection of substitution values

Yes

Interference suppression, error limits
Crosstalk between outputs

Max. -40 dB

Operational limit (over the entire temperature

range, referenced to output range)

±0.2%

Basic error limit (operational limit at 25 °C,

referenced to output range)

±0.15%

Temperature error (referenced to output range)

Max. ±0.01%/K

Linearity error (referenced to output range)

±0.02%

Repeat accuracy (in steady state at 25 °C,

referenced to output range)

±0.05%

Output ripple (referenced to output range),

bandwidth 0 to 50 kHz

±0.02%

Status, interrupts, diagnostics
Interrupts

•

Hardware interrupt

•

Diagnostic interrupt

Configurable

Diagnostic functions

•

Group error display

Red LED (SF)

•

Channel error display

Yes

•

Diagnostic functions can be read out

Yes

Monitoring for

•

Short-circuit

Yes; however, the diagnostic function cannot

detect a short-circuit in the zero range

•

Wire break

Isolation
Isolation tested with

500 V DC

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands