Siemens Simatic ET200pro Operating Instructions Manual Download Page 387

Page: 387 / 545

Analog electronic modules

15.1 Analog electronic module 4 AI U High Feature (6ES7144-4FF00-0AB0)

ET 200pro distributed I/O system
Operating Instructions, 03/2013, A5E00335544-08

387

Technical specifications

•

Resolution (including overrange)

± 10 V/15 bit + sign

± 5 V/15 bit + sign

0 V to 10 V/15 bit; 14 bit with low-level

smoothing.

1 V to 5 V/15 bit; 14 bit with low-level smoothing.

Measured value smoothing

Yes, can be assigned in 4 steps

Step
None

Weak

Medium

Strong

Time constant
1 x cycle time

4 x cycle time

16 x cycle time

64 x cycle time

Interference suppression, error limits
Interference voltage suppression for f = n x (f1 ±1 %), (f1 = interference frequency)

•

Common mode interference

(interference voltage < 5 V)

Min. 70 dB

•

Series-mode interference (signal value + peak

value of interference < rated value of input

range)

Min. 50 dB

Crosstalk between inputs

Max. -50 dB

Operational limit (across temperature range,

referenced to input range)

±0.15%

Basic error limit (operational limit at 25 °C,

referenced to input range)

±0.1%

Temperature error (referenced to input range)

Max. ±0.002 %/K

Linearity error (referenced to input range)

±0.01%

Repeat accuracy (in steady state at 25 °C,

referenced to input range)

±0.025%

Status, interrupts, diagnostics
Interrupts

•

Process interrupt (limit value interrupt)

Configurable for channel 0

•

Diagnostic interrupt

Configurable

Diagnostic functions

•

Group error display

Red LED (SF)

•

Channel error display

Yes

•

Diagnostic functions can be read out

Yes

Monitoring for

•

Short-circuit

Yes, at 1 V to 5 V

•

Wire break

Yes, at 1 V to 5 V

Isolation
Isolation tested with

500 V DC

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands