Siemens Simatic ET200pro Operating Instructions Manual Download Page 316

Page: 316 / 545

Interface modules

12.2 Interface modules for PROFINET IO

ET 200pro distributed I/O system

316

Operating Instructions, 03/2013, A5E00335544-08

Technical specifications

Technical specifications
Dimensions and weight
Dimensions W × H × D (mm)

135 x 130 x 60

Weight

Approx. 490 g

Module-specific data
Transfer rate

100 Mbit/s full duplex

Transmission procedure

100BASE-TX

Autonegotiation

Yes

Bus protocol

PROFINET IO

Supported Ethernet services

PROFINET IO (Device),

TCP/IP Protocol Suite:

•

Network management functions

•

ping

•

arp

Network diagnostics (SNMP)

PROFINET interface

•

Connection socket

2 x M12 d-coded

•

Switch function

Yes, internal

•

Auto-cross-over

Yes; for segment expansion with additional IO

devices or for connection of a PG

VendorID

002A

DeviceID

0305

Voltages and currents
Rated supply voltage of the electronic

components (1L+)

24 V DC

•

Reverse polarity protection

Yes; against destruction

•

Short-circuit protection

Yes; with replaceable fuses

•

Feed current 1L+

Max. 5 A; per ET 200pro

Rated load voltage 2L+

24 V DC(integrated power module)

•

Reverse polarity protection

Yes; against destruction

•

Short-circuit protection

Yes, for the potential group

•

Feed current 2L+

Max. 10 A; per ET 200pro

Current consumption
From rated supply voltage (1L+)

Typ. 250 mA; with CM IM PN M12, 7/8" or

CM IM PN PP Cu
Typ. 350 mA; with CM IM PN PP FO

Power loss of the module

Typ. 6 W; with CM IM PN M12, 7/8" or

CM IM PN PP Cu
Typ. 6.7 W; with CM IM PN PP FO

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands