Siemens Simatic ET200pro Operating Instructions Manual Download Page 169

Page: 169 / 545

Maintenance and service

7.7 Updating the interface module firmware

ET 200pro distributed I/O system
Operating Instructions, 03/2013, A5E00335544-08

169

7.7.2

Firmware Update of IM 154-1 DP, IM 154-2 DP High Feature

Introduction

The procedure below describes the firmware update of IM 154-1 DP or IM 154-2 DP High

Feature interface modules via the PROFIBUS DP interface.

Requirements

●

The interface module of the station to be updated must be online.

Procedure

Connect the PG/PC containing the update files via the PROFIBUS DP interface.
For information on procedures, refer to the STEP 7 online help.

Restart after update

On the STEP 7 user interface, you can define

●

whether the interface module performs an automatic reset after a successful update to

restart with the new firmware

●

whether the interface module is to be reset by switching the electronic/encoder supply

1L+ off before the interface module starts with the new firmware after switching 1L+ on

again

CAUTION

If the "Update firmware after download" checkbox is set, a brief failure of the ET 200pro

station is triggered. If you have not made any provisions for this situation, the update will

result in a CPU STOP due to a rack failure.

If the update fails, the interface module will always restart with its current ("old") firmware

version after you switch 1L+ off and on.

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands