Siemens Simatic ET200pro Operating Instructions Manual Download Page 84

Page: 84 / 545

Connection

4.5 Connecting the interface module to a CM IM DP Direct connection module

ET 200pro distributed I/O system

Operating Instructions, 03/2013, A5E00335544-08

4.5.4

Connecting PROFIBUS DP

Connecting the PROFIBUS DP cable

Open the black strain relief using a crosstip screwdriver.

Open the transparent insert of the insulation displacement terminal.

Feed the incoming PROFIBUS DP cable into insert A/B of the insulation displacement

terminal DP1. Wire red to red, and green to green accordingly.

When forwarding the PROFIBUS DP cable, terminate it at insert A/B of the insulation

displacement terminal DP2.

Push the insert firmly down onto the contact.

Secure the black strain relief using a crosstip screwdriver.

①

Shield support for cable

Figure 4-10 View of open PROFIBUS cable connector

Note
You may leave insulation residue in the insulation displacement terminal when you open

it. This may pose a problem the next time you connect a wire. You should thus always

ensure not to leave any insulation residue in the insulation displacement terminal when

you open it and remove the wire.

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands