Siemens Simatic ET200pro Operating Instructions Manual Download Page 449

Page: 449 / 545

Analog electronic modules

15.13 Influence of the range of values

ET 200pro distributed I/O system
Operating Instructions, 03/2013, A5E00335544-08

449

15.13

Influence of the range of values

Influence of analog signals on input values

The reaction of electronics modules with analog inputs depends on the position of input

values within the range of values. The table below shows this dependency.

The measured value is

Result

GE LED

Diagnostics data range of

the module

Interrupt

Within the nominal range

Measured

value

Within the overrange/undershoot

range

Measured

value

Within the overflow range

7FFF

lit

Entry

Diagnostic interrupt

Within the underflow range

8000

lit

Entry

Diagnostic interrupt

Above the high limit, or below the low

limit

Measured

value

Process interrupt

Out of the parameterization range, or

with faulty parameters

7FFF

/meas

ured value

lit

Entry

Diagnostic interrupt

If the group diagnostics and measuring range parameters are enabled at the analog input module.

If the process interrupt parameter is enabled at the analog input module.

A module parameterized correctly continues operation with its correct parameters.

Influence of output values on analog outputs

The reaction of electronic modules with analog outputs depends on the position of the input

values within the range of values. The table below shows this dependency.

The output value is

Result

GE LED

Diagnostics data range

of the module

Interrupt

Within the nominal range

Value from the

DP master/

IO controller

Within the overrange/undershoot

range

Value from the

DP master/

IO controller

Within the overflow range

0 signal

Within the underflow range

0 signal

Out of the parameterization range,

or with faulty parameters

0 signal

lit

Entry

Diagnostic interrupt

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands