Lenovo System x3500 M5 Type 5464 Installation And Service Manual Download Page 98

Page: 98 / 1236

000000000

000

0000

Back View

Bracket

Adapter

Figure 67. Rotate the adapter-retention brackets to the open position

Step 9.

Remove the PCIe slot filler, if installed. Keep the filler in a safe place for potential future use.

Step 10. Press the adapter

firmly

into the expansion slot.

000

Expansion
slot cover

Adapter

Bracket

Back View

Figure 68. Press adapter into expansion slot

Attention:

Incomplete insertion might cause damage to the system board or the adapter.

Step 11. Close the adapter-retention bracket.

System x3500 M5 Installation and Service Guide

Summary of Contents for System x3500 M5 Type 5464





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3500 M5 Type 5464

Reviews:

Related manuals for System x3500 M5 Type 5464

Brands by name

Popular brands

Lenovo System x3500 M5 Type 5464, Installation And Service Manual

Search results

Summary of Contents for System x3500 M5 Type 5464

Reviews:

Related manuals for System x3500 M5 Type 5464

Brands by name

Popular brands