Lenovo System x3500 M5 Type 5464 Installation And Service Manual Download

Page: 66 / 1236

Bezel lock

Figure 36. Unlock the left-side cover

Step 2.

Carefully turn the server on its side so that it is lying flat, with the cover facing up.

Step 3.

Press the cover-release latch down while you rotate the top edge of the cover away from the
server; then, lift the cover off the server.

0000000000

000000000000

Cover release latch

Left side cover

Figure 37. Left-side cover removal

Removing the air baffle

Use this information to remove the air baffle from the server.

Read the safety information in “Safety” on page v and “Installation guidelines” on page 29.

System x3500 M5 Installation and Service Guide

Summary of Contents for System x3500 M5 Type 5464





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3500 M5 Type 5464

Reviews:

Related manuals for System x3500 M5 Type 5464

Brands by name

Popular brands

Lenovo System x3500 M5 Type 5464, Installation And Service Manual

Search results

Summary of Contents for System x3500 M5 Type 5464

Reviews:

Related manuals for System x3500 M5 Type 5464

Brands by name

Popular brands