manualshive.com logo in svg

Lenovo System x3500 M5 Type 5464, Installation And Service Manual

Share
Download
Lenovo System x3500 M5 Type 5464 Installation And Service Manual Download Page 114

Step 6.

Install the server in the rack cabinet (see the

Tower to Rack Installation Instructions

that come with

the server for instructions).

Step 7.

Slide the server back into the rack, if necessary.

Step 8.

Start the server. Confirm that it starts correctly and recognizes the newly installed devices, and
make sure that no error LEDs are lit.

Step 9.

( Business Partners only) Complete the additional steps in “Instructions for Business Partners”
on page 23.

Replacing the fan cage assembly

Use this information to replace the fan cage assembly.

Attention:

Make sure that all wires and cables inside the server are routed correctly before you install

the fan cage assembly. Wiring that is not properly routed might be damaged or might prevent the fan
cage assembly from seating properly in the server.

Read the safety information in “Safety” on page v and “Installation guidelines” on page 29.

To replace the fan cage assembly, complete the following steps.

Step 1.

Align the guides on the fan cage with the release latch to the open position on each side.

Step 2.

Push the fan cage assembly into the server.

Note:

Make sure that the fan cage is fully seated.

Step 3.

Rotate the fan cage release latch to the close position. The fan cage will be fully seated when it
is secured.

00

00

00000000000

00000000000

00000000000

00000000000

00000000000

00000000000

00000000000

00000000000

00000000000

00

0

0

00

00

00

00

0000000000000

0000000000000

0000000000000

0000000000000

0000000000000

0000000000000

0000000000000

0000000000000

0000000000000

0000000000000

0000000000000

0000000000000

0000000000000

1

2

Fan cage assembly

Figure 89. Rotate the fan cage release latch

Step 4.

Connect the fan cage assembly power cable to the system board (see “Internal cable routing and
connectors” on page 33).

98

System x3500 M5 Installation and Service Guide

Summary of Contents for System x3500 M5 Type 5464





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands