manualshive.com logo in svg

Lenovo System x3500 M5 Type 5464, Installation And Service Manual

Share
Download
Lenovo System x3500 M5 Type 5464 Installation And Service Manual Download Page 288

Step 4.

Remove the heat sink:

Attention:

Do not touch the thermal material on the bottom of the heat sink. Touching the thermal

material will contaminate it. If the thermal material on the microprocessor or heat sink becomes
contaminated, you must wipe off the contaminated thermal material on the microprocessor or heat
sink with the alcohol wipes and reapply clean thermal grease to the heat sink.

a.

Rotate the heat sink release lever to the fully open position.

Heat sink

Heat sink 
release lever

Figure 192. Rotate the heat sink release lever to the open position

b.

Remove the heat sink out of the server. After removal, place the heat sink (with the thermal
grease side up) on a clean, flat surface.

Heat sink

Heat sink 
release lever

Lock tab

Figure 193. Remove the heat sink out of the server

Step 5.

Open the microprocessor socket release levers and retainer:

272

System x3500 M5 Installation and Service Guide

Summary of Contents for System x3500 M5 Type 5464





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands