Home
/
Lenovo
/
System x3500 M5 Type 5464
/
Installation And Service Manual

Lenovo System x3500 M5 Type 5464, Installation And Service Manual

Share

Page: 104 / 1236

Lenovo System x3500 M5 Type 5464 Installation And Service Manual Download Page 104

Note:

Do not touch the microprocessor contacts. Contaminants on the microprocessor

contacts, such as oil from your skin, can cause connection failures between the contacts
and the socket.

b.

Align the installation tool with the microprocessor socket and lower down the installation tool.
The installation tool rests flush on the socket only if properly aligned.

Installation tool

Microprocessor

Alignment pins

Figure 74. Installation tool alignment

c.

Install the microprocessor using the following instructions for your installation tool.

• Twist the handle of the installation tool assembly counterclockwise to the unlocked position

until you can not twist the handle any further; then, lift the installation tool out of the socket.

Figure 75. Installation tool handle adjustment

The following illustrations show the installation tool in the locked and unlocked positions.

88

System x3500 M5 Installation and Service Guide

«
...
102
103
104
105
106
...
»

Summary of Contents for System x3500 M5 Type 5464





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands