manualshive.com logo in svg

Lenovo System x3500 M5 Type 5464, Installation And Service Manual

The Lenovo System x3500 M5 Type 5464 is a powerful server designed to meet the demands of modern businesses. To get the most out of this exceptional product, you can easily access its detailed Product Manual for free download at manualshive.com. Whether you're a tech enthusiast or IT professional, this manual is an invaluable resource for understanding and maximizing your server's capabilities.

Share
Download
background image

Note:

When you install any RAID adapter that comes with batteries, it is sometimes necessary to install the

batteries in another location in the server to prevent the batteries from overheating.

Read the safety information in “Safety” on page v and “Installation guidelines” on page 29.

If you are replacing a server component in the server, you need to turn off the server and peripheral devices,
and disconnect the power cords and all external cables.

To install a RAID adapter battery or flash power module remotely in the server, complete the following steps.

Step 1.

Unlock and remove the left-side cover (see “Removing the left-side cover” on page 49).

Step 2.

Remove the air baffle (see “Removing the air baffle” on page 188).

Step 3.

Install the ServeRAID adapter on the system board (see “Installing an adapter” on page 216).

Step 4.

Connect one end of the battery/flash power module cable to the battery/flash power module
connector.

Step 5.

Install the battery/flash power module:

a.

Align the battery/flash power module cable connector with the slot on the battery/flash power
module holder. Place the battery/flash power module into the battery/flash power module
holder and make sure that the battery/flash power module holder engages the battery/flash
power module securely.

1

2

Battery / flash power module

Battery holder

Retention clip

Figure 70. Align the battery/flash power module cable connector

Note:

The positioning of the remote battery/flash power module depends on the type of the

remote batteries/flash power module that you install.

b.

Connect the other end of the battery/flash power module cable to the battery/flash power
module cable connector on the battery/flash power module.

c.

Lower and press down on the retention clip until it snaps in place to hold the battery/flash
power module firmly in place.

If you have other devices to install or remove, do so now. Otherwise, go to “Completing the installation”
on page 97.

Installing a microprocessor and heat sink

Use this information to install a microprocessor and heat sink.

84

System x3500 M5 Installation and Service Guide

Summary of Contents for System x3500 M5 Type 5464





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3500 M5 Type 5464

Aastra 400 Series System Manual preview
400 Series
Brand: Aastra Pages: 592
Supero 6027R-E1R12N User Manual preview
6027R-E1R12N
Brand: Supero Pages: 112
Lucent Technologies Definity 8510T User Manual preview
Definity 8510T
Brand: Lucent Technologies Pages: 85
IBM System x3650 M5 Installation And Service Manual preview
System x3650 M5
Brand: IBM Pages: 1010
Tangent Thin Client 166 Datasheet preview
Thin Client 166
Brand: Tangent Pages: 2
Atop ABLELink GW21W User Manual preview
ABLELink GW21W
Brand: Atop Pages: 52
IOGear GPSU21 Installation Manual preview
GPSU21
Brand: IOGear Pages: 48
myTEM MTSER-100-WL Quick Start Manual preview
MTSER-100-WL
Brand: myTEM Pages: 2
Toshiba RS-TX60 Specification Sheet preview
RS-TX60
Brand: Toshiba Pages: 2
Toshiba BMS-LSV6E Installation Manual preview
BMS-LSV6E
Brand: Toshiba Pages: 8
Toshiba BMS-LSV6UL Installation Manual preview
BMS-LSV6UL
Brand: Toshiba Pages: 12
Toshiba BMS-LSV4E Installation Manual preview
BMS-LSV4E
Brand: Toshiba Pages: 8
Toshiba C1 Installation Manual preview
C1
Brand: Toshiba Pages: 16
Toshiba IPedge EP Server Product Bulletin preview
IPedge EP Server
Brand: Toshiba Pages: 19
Toshiba SD-H400 - Combination Progressive-Scan DVD Player Service Manual preview
SD-H400 - Combination Progressive-Scan DVD Player
Brand: Toshiba Pages: 53
Toshiba MAGNIA 510D User Manual preview
MAGNIA 510D
Brand: Toshiba Pages: 185
Toshiba Digital Media Server Viewer'S Manual preview
Digital Media Server
Brand: Toshiba Pages: 204
Toshiba Magnia 550D User Manual preview
Magnia 550D
Brand: Toshiba Pages: 241

Brands by name

Popular brands

Load more brands