manualshive.com logo in svg

Lenovo System x3500 M5 Type 5464, Installation And Service Manual

Share
Download
Lenovo System x3500 M5 Type 5464 Installation And Service Manual Download Page 335

No

Automatically notify support

No

Alert Category

System - other

SNMP Trap ID

22

CIM Information

Prefix:

IMM

ID:

0029

User Response

Complete the following steps until the problem is solved:

1. Reconfigure the watchdog timer to a higher value.

2. Make sure that the IMM Ethernet over USB interface is enabled.

3. Reinstall the RNDIS or cdc_ether device driver for the operating system.

4. Disable the watchdog. Check the integrity of the installed operating system.

5. Update the IMM firmware. Important: Some cluster solutions require specific code levels or

coordinated code updates. If the device is part of a cluster solution, verify that the latest level of
code is supported for the cluster solution before you update the code.

•

4000001e-00000000 : Running the backup Management Controller [arg1] main application. ()

This message is for the use case where a Management Controller has resorted to running the backup
main application.

May also be shown as 4000001e00000000 or 0x4000001e00000000

Severity

Warning

Serviceable

No

Automatically notify support

No

Alert Category

System - other

SNMP Trap ID

22

CIM Information

Prefix:

IMM

ID:

0030

User Response

Update the IMM firmware. Important: Some cluster solutions require specific code levels or
coordinated code updates. If the device is part of a cluster solution, verify that the latest level of code
is supported for the cluster solution before you update the code.

Appendix A. Integrated Management Module II (IMM2) error messages

319

Summary of Contents for System x3500 M5 Type 5464





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands