Juniper QFX3000-G QFabric Deployment Manual Download Page 644

Page: 644 / 652

In the

Switching

box, click

Junos OS Platforms

In the

QFX Series

section, click the name of the platform for which you want to

download software.

Click the

Software

tab and select the release number from the

Release

drop-down

list.

Select the complete install media you want to download in the

QFabric System Install

Media

section.

A login screen appears.

Enter your name and password and press

Enter

Read the End User License Agreement, click the

I agree

radio button, and then click

Proceed

10.

Use FTP to access the UNIX workstation where the install media resides.

ftp ftp://

hostname/pathname install-media-qfabric-<version>

.img.tgz

11.

When prompted, enter your username and password.

12.

Make sure you are in binary mode by entering

binary

at the prompt.

binary

13.

Use the

get

command to transfer the installation package from the FTP host to your

UNIX workstation.

get

install-media-qfabric-<version>

.img.tgz

14.

Close the FTP session:

bye

15.

Untar the

install-media-qfabric-<version>

.img.tgz file on your UNIX workstation.

tar -xvzf install-media-qfabric-11.3X30.6.img.tgz

16.

Insert a blank external USB (4-gigabyte) flash drive supplied by Juniper Networks into
your UNIX workstation.

17.

Burn the software image you just downloaded to your UNIX workstation onto your
external USB flash drive using the

command:

dd if=install-media-qfabric-11.3X30.6.img of=/dev/sdb bs=16k

0 records in
0 records out
4110417920 bytes (4.1 GB) copied, 5.10768 seconds, 805 MB/s

18.

Perform the steps in

“Performing a Recovery Installation Using a Juniper Networks

External USB Flash Drive with Preloaded Software” on page 618

to continue with the

recovery installation.

Performing a Recovery Installation Using a Juniper Networks External USB Flash Drive with
Preloaded Software

Supported Platforms

QFabric System

618

QFX3000-G QFabric System Deployment Guide

Summary of Contents for QFX3000-G QFabric
























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for QFX3000-G QFabric

Reviews:

Juniper QFX3000-G QFabric, Deployment Manual, Page: 644 / 652

Search results

Summary of Contents for QFX3000-G QFabric

Reviews: