Juniper QFX3000-G QFabric Deployment Manual Download Page 60 | Manualshive

Page: 60 / 652

Juniper QFX3000-G QFabric Deployment Manual Download Page 60

Figure 10: QFabric System Topology - Default Partition

Interconnect devices

Virtual Chassis

control plane

Director devices

Node devices

g041145

NOTE:

The initial release of the QFabric system supports a single default

partition. All equipment and resources belong to the default partition.

A partition provides the following functions:

•

Fault isolation and separation from other partitions at the control plane level.

•

A separate configuration domain for the Node devices within the partition.

•

A Layer 2 domain in which MAC learning takes place, and members of the same VLAN
can communicate with each other. To provide network connectivity between partitions,
you need to enable Layer 3 routing by way of a routed VLAN interface (RVI).

Related

Documentation

Gaining Access to the QFabric System Through the Default Partition on page 373

•

•

Understanding the QFabric System Software Architecture on page 31

•

Understanding the QFabric System Hardware Architecture on page 15

Copyright © 2015, Juniper Networks, Inc.

34

QFX3000-G QFabric System Deployment Guide

«
...
58
59
60
61
62
...
»

Summary of Contents for QFX3000-G QFabric













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments