manualshive.com logo in svg

Juniper QFX3000-G QFabric, Deployment Manual, Page: 175 / 652

Share
Download
Juniper QFX3000-G QFabric Deployment Manual Download Page 175

Figure 19: Mounting a QFX3100 Director Device on Four Posts in a Rack
or Cabinet

g050061

Related

Documentation

Connecting Earth Ground to an EX Series Switch

•

•

Connecting AC Power to a QFX3100 Director Device on page 149

•

Installing and Connecting a QFX3100 Director Device on page 143

•

Rack-Mounting and Cabinet-Mounting Warnings

Connecting AC Power to a QFX3100 Director Device

Supported Platforms

QFabric System

The power supply in a QFX3100 Director device is a hot-removable and hot-insertable
field-replaceable unit (FRU) located on the far right side of the rear panel. You can remove
and replace a single power supply without powering off the QFX3100 Director device or
disrupting QFX3100 Director device functions.

Before you begin connecting AC power to a QFX3100 Director device:

•

Install the power supply in the chassis. See

Installing a Power Supply in a QFX3100

Director Device

.

NOTE:

Each power supply must be connected to a dedicated power source

outlet to ensure power supply redundancy.

149

Copyright © 2015, Juniper Networks, Inc.

Chapter 9: Installing a QFX3100 Director Device

Summary of Contents for QFX3000-G QFabric













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments