Juniper QFX3000-G QFabric Deployment Manual Download Page 211

Page: 211 / 652

If the wiring tray is installed in the chassis, remove it. See

Removing a Wiring Tray from

a QFX3008-I Interconnect Device

. The power cord must be attached to the wiring tray

as described in

“Preparing Delta and Wye Three-Phase Power Cords” on page 178

Ensure that the power switch on the wiring tray faceplate is in the OFF (O) position.

Using a number 1 Phillips (+) screwdriver, loosen the four screws on the metal AC
wiring compartment on the side of the wiring tray (see

Figure 35 on page 186

Open the metal door of the wiring tray compartment.

185

Chapter 10: Installing a QFX3008-I Interconnect Device

Summary of Contents for QFX3000-G QFabric
























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for QFX3000-G QFabric

Reviews:

Juniper QFX3000-G QFabric, Deployment Manual, Page: 211 / 652

Search results

Summary of Contents for QFX3000-G QFabric

Reviews: