Juniper QFX3000-G QFabric Deployment Manual Download Page 547

Page: 547 / 652

Table 93: show chassis ethernet-switch interconnect-device fpc Output Fields

(continued)

Field Description

Field Name

Number of received packets of size 2048 through 4095 octets.

RX Packets
2048-4095 Octets

Number of received packets of size 4096 through 9216 octets.

RX Packets 4096-9216
Octets

Number of multicast packets received.

RX Multicast Packets

Number of broadcast packets received.

RX Broadcast Packets

Number of packets discarded because of frame check sequence errors.

RX FCS Errors

Number of incomplete octets received.

RX Align Errors

Number of fragmented packets received.

RX Fragments

Number of symbols received that the router did not correctly decode.

RX Symbol errors

Number of packets received with unsupported op codes.

RX Unsupported
opcodes

Number of packets received with an out of range length.

RX Out of Range
Length

Number of packets received with false carrier errors.

RX False Carrier Errors

Number of undersized packets received.

RX Undersize Packets

Number of oversized packets received.

RX Oversize Packets

Total number of frames received that exceed the maximum byte count and contain CRC errors .

RX Jabbers

RX 1519-1522 Good
Vlan frms

Number of packets received that exceed the MTU.

RX MTU Exceed
Counter

Number of control frames received.

RX Control Frame
Counter

Number of pause frames received.

RX Pause Frame
Counter

Number of bytes received.

RX Byte Counter

521

Chapter 21: Operational Mode Commands

Summary of Contents for QFX3000-G QFabric
























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for QFX3000-G QFabric

Reviews:

Juniper QFX3000-G QFabric, Deployment Manual, Page: 547 / 652

Search results

Summary of Contents for QFX3000-G QFabric

Reviews: