IDT Tsi578 User Manual Download | Manualshive

Page: 498 / 527

background image

B. Clocking > P_CLK Programming

498

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

•

Period (START_SETUP) = (START_SETUP * Period(PCLK))

— PCLK is 10ns

— Reset time is 4.71 microseconds.

— Tsi578 reset value is 0x01D7

START_HOLD Count for the START Condition Hold Period

The START_HOLD field defines the minimum hold time for the START condition; that is, from
I2C_SD seen low to I2C_SCLK pulled low. This is a master only timing parameter.

•

Period (START_HOLD) = (START_HOLD * Period(P_CLK))

•

P_CLK is 10 ns

•

Reset time is 4.01 microseconds

•

Tsi578 reset value is 0x0191

B.2.3.3

I2C Stop/Idle Timing Register

The I2C Stop/Idle Timing Register programs the setup timing for the Stop condition when generated by
the master control logic and the Idle Detect timer.

The Stop/Idle register is broken down as follows:

•

The timer period for the STOP_SETUP is relative to the reference clock

•

The timer period for the Idle Detect is relative to the USDIV period

•

The STOP_SETUP time is shadowed during boot loading, and can be reprogrammed prior to a
chain operation without affecting the bus timing for the current EEPROM.

STOP_SETUP Count for STOP Condition Setup Period

The STOP_SETUP field defines the minimum setup time for the STOP condition (that is, both
I2C_SCLK seen high and I2C_SD seen low prior to I2C_SD released high). This is a master-only
timing parameter.

•

Period(STOP_SETUP) = (STOP_SETUP * Period(P_CLK))

— P_CLK is 10ns

— Reset time is 4.01 microseconds

— Tsi578 reset value is 0x0191

Ti

p

The START_SETUP time doubles as the Stop Hold.

«
...
496
497
498
499
500
...
»

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Tsi578

LambdaUnite MSS

Brand: Lucent Technologies Pages: 388

LVP-51 LVP-51 Series

Brand: Omega Engineering Pages: 6

Brand: Comtrend Corporation Pages: 2

UHB-U3P1U2P3P-01

Brand: Gembird Pages: 2

Brand: ADC Pages: 75

Brand: Alloy Pages: 33

Brand: Raritan Pages: 4

Genesis Digital HSM-04-02

Brand: Hall Research Technologies Pages: 28

Brand: TCi Pages: 11

Brand: Zektor Pages: 30

Brand: Black Box Pages: 2

Brand: Gefen Pages: 48

Brand: Edge-Core Pages: 15

DCRS-5200 Series

Brand: Digital China Networks Pages: 4

Brand: A-Neuvideo Pages: 20

Brand: Veris Industries Pages: 2

MAGTOP Snap 201

Brand: Bamo Pages: 2

Brand: Intellinet Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands