manualshive.com logo in svg

IDT Tsi578, User Manual

The IDT Tsi578 is a high-performance networking switch, and to help you make the most out of its features, we provide a comprehensive User Manual. This manual is available for free download from our website, ensuring effortless access to valuable product information and instructions for optimal usage.

Share
Download
background image

12. Serial RapidIO Registers > IDT-Specific RapidIO Registers

320

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

8

DEBUG_MODE

Mode of operation

0 = Normal

1 = Debug mode

Debug mode unlocks the capture registers for writing and enables 
the debug packet generator feature.

R/W

0

9

SEND_DBG_PKT

Send Debug Packet

0 = Normal

1 = Send debug packet

This bit is set by software and is cleared by hardware after the 
debug packet is sent. Writes when the bit is already set are ignored.

Debug mode only.

R/W

0

10:11

Reserved

N/A

R

0

12

PORT_ERR_EN

Port Error Enable

An interrupt and/or port-write is generated if there is a Port Error.

R/W

0

13

MC_TEA_EN

Multicast TEA Enable

An interrupt and/or port write is generated when the multicast engine 
has timed out before it could deliver a packet to the broadcast buffer.

R/W 0

14

LINK_INIT_NOTIF

ICATION_EN

Enables interrupts and port writes for LINK_INIT_NOTIFICATION 
events.

0 = Interrupt and/or port write disabled

1 = Interrupt and/or port write enabled 

R/W

0

15

LUT_PAR_ERR_

EN

Enables interrupts for parity errors in the lookup table.

0 = Interrupt disabled

1 = Interrupt enabled

R/W

0

16:23

MAX_RETRY_TH

RESHOLD

Maximum Retry Threshold

These bits provide the threshold value for reporting congestion at an 
outbound switch buffer caused by congestion at the link partner. 

When the number of consecutive retries reaches this threshold, the 
switch generates a port-write and sends the IMP_SPEC_ERR bit in 
the RapidIO Port x Error Detect CSR.

00 = Disable the RETRY_ERROR reporting

01 = Set the MAX_RETRY_THRESHOLD to 1

02 = Set the MAX_RETRY_THRESHOLD to 2

...

FF = Set the MAX_RETRY_THRESHOLD to 255

R/W

0x00

24

ILL_TRANS_ERR

Illegal Transfer Error Reporting Enable 

If enabled, the port-write and/or interrupt report an error when the 
ILL_TRANS_ERR bit is set.

R/W

0

 (Continued)

Bits

Name

Description

Type

Reset

Value

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Tsi578

CALIENT S320 Repair And Diagnostics Field Manual preview
S320
Brand: CALIENT Pages: 22
Baxall DVS24 Installation And Operating Instructions Manual preview
DVS24
Brand: Baxall Pages: 33
Accton Technology EtherHub-16 Quick Start Manual preview
EtherHub-16
Brand: Accton Technology Pages: 10
Lancom GS-3528X Installation Manual preview
GS-3528X
Brand: Lancom Pages: 23
Ruby Tech GS-2108C User Manual preview
GS-2108C
Brand: Ruby Tech Pages: 254
Sunix ESW-5162GP User Manual preview
ESW-5162GP
Brand: Sunix Pages: 55
Origin Instruments Swifty SW2 User Manual preview
Swifty SW2
Brand: Origin Instruments Pages: 6
ATEN CS62T User Manual preview
CS62T
Brand: ATEN Pages: 21
Gefen HDTV-441 Manual preview
HDTV-441
Brand: Gefen Pages: 9
Eminent EM1019 Instruction Manual preview
EM1019
Brand: Eminent Pages: 6
Orbis DICROMAT+ User Instructions preview
DICROMAT+
Brand: Orbis Pages: 2
PCB Piezotronics IMI Sensors 691A80 Installation And Operating Manual preview
IMI Sensors 691A80
Brand: PCB Piezotronics Pages: 15
ATEN CS-102U User Manual preview
CS-102U
Brand: ATEN Pages: 15
Tripp Lite B004-008 Owner'S Manual preview
B004-008
Brand: Tripp Lite Pages: 9
Lindy 32937 Manual preview
32937
Brand: Lindy Pages: 8
Key Digital Champion KD-4X4XC Setup Manual preview
Champion KD-4X4XC
Brand: Key Digital Pages: 8
Atlona AT-PRO2HD88M User Manual preview
AT-PRO2HD88M
Brand: Atlona Pages: 17
SBC Q.NET-5TX User Manual preview
Q.NET-5TX
Brand: SBC Pages: 28

Brands by name

Popular brands

Load more brands