IDT Tsi578 User Manual Download | Manualshive

Page: 156 / 527

background image

7. I

2

C Interface > Tsi578 as I

2

C Slave

156

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

7.5.5

Slave Write Data Transactions

An external master must set the peripheral address as part of a write transaction before transferring any
data. The effect of the written data depends on the register in which the peripheral address maps (see

). The peripheral address is usually incremented after each byte such that consecutive bytes are

written into increasing addresses within the peripheral address space. Certain exceptions exist,
however, as indicated in

. In addition, a write that hits the most significant byte of the

“Externally Visible I

C Internal Write Address Register”

(peripheral address 0x07) has the side-effect

of triggering a write to a register on the Tsi578 internal register bus.

0x20–0x23

Read-Only

EXI2C_ACC_STAT

Returns status information on accesses performed by external devices,
on the incoming/outgoing mailboxes and on the state of the alert
response flag.

0x24–0x27

R/W

EXI2C_ACC_CNTRL

Provides control information on how the Tsi578 handles internal register
accesses through the EXI2C_REG_RDATA and EXI2C_REG_WDATA
registers.

0x28–0x7F

Read-Only

Reserved

This range does not map to any registers.

0x80–0x83

Read-Only

EXI2C_STAT

Returns a summary of the internal status of the Tsi578

.

0x84–0x87

R/W

EXI2C_STAT_
ENABLE

Enables the bits in the status summary (EXI2C_STAT) to set the alert flag
in the EXI2C_ACC_STAT register

.

0x88–0x8B

Read-Only

Reserved

This range does not map to any registers.

0x90–0x93

Read-Only

EXI2C_MBOX_OUT

This register allows a RapidIO-enabled processor to transfer a 32-bit
message to an external I2C master.

0x94–0x97

R/W

EXI2C_MBOX_IN

This register allows an external I2C master to transfer a 32-bit message
to a RapidIO-enabled processor.

0x98–0xFF

Read-Only

Reserved

This range does not map to any registers.

Side effects: When peripheral address 0xFF is read or written, the
peripheral address wraps back to 0x00.

Table 17: Externally Visible I

2

C Register Map (Continued)

Tsi578 Peripheral

Address Range

Mapped Register

Description

«
...
154
155
156
157
158
...
»

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Tsi578

Brand: AVE Pages: 2

Brand: Kobold Pages: 10

SwitchMan USB-Combo SW2

Brand: Raritan Pages: 2

Brand: Steren Pages: 13

Brand: Advantech Pages: 101

Brand: Clas Ohlson Pages: 5

OpenGear DSS-8224

Brand: Ross Pages: 47

Brand: Black Box Pages: 4

Brand: Minicom DX Pages: 36

AVlink VAX-8404F

Brand: C&C TECHNIC Pages: 2

CT-HDVD-4X14K-SW

Brand: NB Pages: 23

Brand: SMART-AVI Pages: 9

DG-GS4900SE Series

Brand: Digisol Pages: 23

S5700-24F-8G-4TF

Brand: Hored Pages: 28

Brand: Omron Pages: 8

Brand: Quark-Elec Pages: 10

Brand: Woodward Pages: 20

Brand: Gefen Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands