IDT Tsi578 User Manual Download | Manualshive

Page: 354 / 527

background image

12. Serial RapidIO Registers > IDT-Specific Performance Registers

354

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

12.9.12

RapidIO Port x Transmitter Output Queue Congestion Period Register

This register is used to monitor the duration of time that the output buffer is in congestion state.

The CONG_PERIOD_CTR counter value is incremented for every N clock cycles specified by the
CONG_PERIOD field in the

“RapidIO Port x Transmitter Output Queue Depth Threshold Register”

while the output buffer is under congestion state. This counter represents the amount of time that the
output buffer is under congestion state.

The CONG_PERIOD_CTR counter value is writable for testing purposes. This counter stops counting
when it reach its maximum value. Reading the CONG_PERIOD_CTR clears the counter value. The
CONG_PERIOD_CTR can be disabled when the CONG_PERIOD field in the

“RapidIO Port x

Transmitter Output Queue Depth Threshold Register”

is set to 0.

Register name: SP{0..15}_TX_Q_PERIOD

Reset value: 0x0000_0000

Register offset: 13088, 13188, 13288, 13388, 13488,

13588, 13688, 13788, 13888, 13988, 13A88,

13B88, 13C88, 13D88, 13E88, 13F88

Bits

0

1

2

3

4

5

6

7

00:7

CONG_PERIOD_CTR

8:15

CONG_PERIOD_CTR

16:23

CONG_PERIOD_CTR

24:31

CONG_PERIOD_CTR

Bits

Name

Description

Type

Reset

Value

0:31

CONG_PERIOD_

CTR

Output Queue Congestion Period Count

Each time the output buffer enters a congestion state, this counter is
incremented for every N clock cycles (as specified in
CONG_PERIOD field of the

“RapidIO Port x Transmitter Output

Queue Depth Threshold Register”

. This counter counts up to

0xFFFFand remains at 0xFFFF until reset.

Note: The counter is reset when read. The counter is enabled if
CONG_PERIOD is set to a value other than 0.

R/W

0x0000

«
...
352
353
354
355
356
...
»

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Tsi578

SmartPro DGS-1500-20

Brand: D-Link Pages: 113

xStack DGS-3120 Series

Brand: D-Link Pages: 1150

Brand: CALIENT Pages: 46

Brand: CALIENT Pages: 42

Brand: D-Box Pages: 27

Brand: G&D Pages: 36

Brand: Pathway connectivity solutions Pages: 2

Brand: Xantech Pages: 20

Brand: AVLT-Power Pages: 12

USB 2.0 7-Port Hub HO97916

Brand: GE Pages: 19

Personal MiniHub

Brand: Black Box Pages: 22

Brand: PIKA Pages: 7

Brand: Lanpro Pages: 16

Brand: J-Tech Digital Pages: 81

Brand: FIBERROAD Pages: 30

Brand: Linksys Pages: 2

Brand: KTI Pages: 25

Brand: Dwyer Instruments Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands