IDT Tsi578 User Manual Download | Manualshive

Page: 154 / 527

background image

7. I

2

C Interface > Tsi578 as I

2

C Slave

154

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

7.5.2

Slave Device Addressing

The Tsi578 supports 7-bit device addressing. The device address of the Tsi578 is set in the SLV_ADDR
field of the

C Slave Configuration Register”

. For the Tsi578 to respond to an external master, the

slave address on the bus must match either the address in the SLV_ADDR field, or the SMBus alert
response address (see

“SMBus Alert Response Protocol Support”

. However, an address of all zeros

(0000000) never triggers a response because this address is used for the START byte and General Call
protocol. Neither the START byte or General Call protocol are supported by the Tsi578.

The SLV_ADDR field can be changed at any time, either using the boot load sequence or by the
processor/host. At power-up, the lower 2 bits of the 7-bit device address (defined by SLV_ADDR) are
loaded from the PWRUP_I2C pins. This allows the user to support up to four separate Tsi578 devices
on the same I

2

C bus. Changing the SLV_ADDR field does not change the value of the lower 2 bits

unless those bits are unlocked by first setting the SLV_UNLK field in the

C Slave Configuration

7.5.3

Slave Peripheral Addressing

The Tsi578 peripheral space comprises an addressable range of 256 bytes (from 0x00 to 0xFF) that can
be directly read and written by an external I

2

C master device. When an external master sets the

peripheral address, this sets a pointer (viewable in the SLV_PA field of the

C Access Status

) maintained in the Tsi578 that determines where bytes read and written by the external

master are within the peripheral address space.

This 256-byte space is mapped to the Externally Visible Registers within the I

2

C Interface; these

registers all start with EXI2C_ (see

“Externally Visible I

C Internal Write Address Register”

registers can be accessed either directly by an external master using the addresses in the peripheral
address space, or by the processor/host using the internal register bus addresses. Depending on how the
registers are accessed also defines their properties: for example, some registers are read-only through
the peripheral address space but read/write through the internal register bus, and vice-versa.

The next section discusses the mapping between the peripheral address space and the externally visible
registers.

If the Tsi578 masters an I

2

C transaction and the device address matches the 7-bit address

programmed by SLV_ADDR, the Tsi578 will respond to its own transaction. This is the only
method that allows software to write to any of the externally visible registers that are
read-only from the internal register bus.

Ti

p

The Tsi578 only responds as a slave if the SLV_EN bit in the

C Slave Configuration

is set to 1.

«
...
152
153
154
155
156
...
»

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Tsi578

RackSwitch G8264

Brand: IBM Pages: 20

Flex System FC3171

Brand: IBM Pages: 64

Baseline 2226 Plus

Brand: 3Com Pages: 4

Brand: jablotron Pages: 2

Brand: CoolGear Pages: 2

Brand: Aruba Pages: 6

Matrix DFE-Gold 4G4202-60

Brand: Enterasys Pages: 78

Brand: ZENEC Pages: 16

Brand: ATEN Pages: 2

Brand: Black Box Pages: 2

Brand: KYLAND Pages: 34

Brand: TRENDnet Pages: 2

Brand: NA-DE Pages: 4

Moeller IZM Series

Brand: Eaton Pages: 4

Brand: Southern States Pages: 32

Brand: N-Tron Pages: 17

Brand: Knightsbridge Pages: 8

kontron KSwitch D1 UGP

Brand: S&T Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands